P.O.Box 1108, MORLEY, 6062, Western Australia
Tel: +61 8 9370 5533 Fax: +61 8 9467 6146
Click here to go to our home page

Send us an e-mail

SC2 Selcall/Telcall Microphone

SC12 Aircraft unit

SC51 Internal vehicle tracking/selcall unit

SC90 Selcall unit for Kenwood TK-90 radios

CM1 Replacement mic for Codan 9323

CM2 Replacement mic for Codan 9323

DM1 DTMF Keypad microphone

CWID1 Repeater/Beacon controller

DT8 DTMF controlled relay unit

FA1 Fleetsync controlled interface unit

Download manuals here

Spares

Download schematics here

Find radio modifications here

We now accept payments via:
AND
Acceptance Mark
Click for more info


Definition: Selcall
Definition: Telcall

CWID-1 Repeater/Beacon controller

The CWID-1 Repeater/Beacon Controller is a small (5cm x 4cm) yet powerful microprocessor controlled unit suitable for use either as a Repeater or a Beacon controller. All functions of the controller are set up using a special programming box (CWID-PROG) and a PC running a Windows programme. The unit is supplied pre-programmed to the customers requirements.

Repeater Mode

When used in the Repeater mode the CWID-1 can transmit an ident of up to 48 characters at a speed of between 5 and 30 wpm. The time between idents can be programmed to be from 10 seconds to 30 minutes in 10 second increments and the ident can be programmed to be suppressed when the repeater is idle. An anti-kerchunk timer is built into the software as is a time out timer and a hold (tail) timer. A courtesy tone (Roger Beep) is available as an option.

Beacon Mode

When used in the Beacon mode the CWID-1 can transmit an ident of up to 48 characters at a speed of between 5 and 30 wpm and can be programmed to give a continuous tone/carrier between idents if required.

Selcall, Selcal, Telcall, Telcal, Decoder, Display CWID-1 Repeater/Beacon Controller manual

Specifications

General Operating power: 8 to 24 VDC nominal, 10 mA maximum.
Outputs available: PTT (o/c active low),
Transmit Keyed Audio
Transmit Keyed DC output (o/c active low)
Inputs to unit:

Carrier Detect (Squelch Line - programmable active high or low), Reset line

Programming: Using special CWID-PROG unit and a PC.
CW Ident length: Maximum 48 characters (A..Z 0..9 , . / ? < > - = Space)
CW Ident speed: 5 to 30 wpm in 1 wpm steps repeated every 10 to 1800 seconds (30 min) in 10 second steps

Transmit time out timer:
(Repeater Mode)

 1 to 10 minutes in 1 minute steps with "Roger Beep" and/or Ident on idle if required.
Hold (Tail) time: 0 to 6 seconds in 100 millisecond steps
CW ident timing:
(Beacon Mode)		 5 to 30 wpm in 1 wpm steps repeated every 10 to 1800 seconds (30 min) in 10 second steps. Tone/carrier between idents if required.
Size: 2.0in Long x 1.6in Wide 0.8in High (max over connector)
50mm Long x 40mm Wide 20mm High (max over connector)
Specifications subject to change without prior notification

For pricing and additional information:

just call or send us an e-mail
Jenal Communications design and manufacture a wide range of radio related devices including units which use the standard HF selcall and telcall signalling as used by Barrett, Codan, Icom and Q-Mac. Thousands of these products are being used all around the world by Governments, NGOs, Commercial organisations and Amateur Radio operators. We also manufacture a number of devices which use the common DTMF (or touchtone) signalling system.

Last modified: 30 June 2011.